How do I reset my master spa hot tub?
Press the red reset button to reset the switch before reaching out to tech support. Make sure the temperature probe is properly in the right amount of water to accurately read the temperature, and that there is no build up in the thermal well.
How do I get my master spa out of economy mode?
Press the “Cool” button to cycle through the Master Spa’s three cycles, Standard, Economy and Sleep. The “Cool” button can be found to the immediate right of the “Program/Mode” button.
What are the codes on a hot tub?
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| FB-ER | Fiber optic error; accent lighting |
| FC | Filter continuous mode; system message, not an error |
| FL1 | Water pressure fault; dirty filter, air locked pump, low water level |
| FL2 | Pressure switch fault; switch closed while pump is off |
How do you fix the code on a hot tub?
How to Troubleshoot a Hot Tub FLO Error Code
- Shut down the spa at the breaker.
- Make sure there is no debris in the water that can get sucked into the pump.
- Take out all of the filter(s) and set them aside.
- Turn spa back on at the breaker with the filters out.
Where is the reset button on a master spa?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.
How do I get my hot tub out of SLP mode?
57 second suggested clip0:111:14Evolution Spa Hot Tub Economy Mode – How to Cycle through the …YouTube
What is SL mode on hot tub?
SL: Sleep – Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What is SE mode on hot tub?
SE = Spa operating in Standard-in-Economy Mode.
What is F2 on hot tub?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
How do I fix the code on my hot tub SNB?
59 second suggested clip0:515:01Hot Tub SN Code Balboa M7 System How To Repair The Spa GuyYouTube
How do I know if my hot tub sensor is bad?
Testing Spa Temperature Sensors Colder water produces higher readings up to 50K, while warmer 100° F water will produce lower readings. Refer to your spa manufacturer resistance vs. temperature chart. Or, if you get “0”, or a zero reading, the sensor or cable is likely bad.
How do I reset my hot tub control panel?
51 second suggested clip0:145:48Reset Hot Spring Spas Control Panel on your Hot Tubs – YouTubeYouTube
What do the Master spas hot tub error messages mean?
In addition to Master Spas hot tub error messages. You may also get a ‘periodic reminder message‘. These are designed to help you remember to undertake proper water care and maintenance. Improper water maintenance is one of the biggest causes of premature hot tub issues as it can damage hot tub components.
Where are master spas hot tubs made?
Master spas hot tub error messages (and how to fix them)… Master Spas are a North American manufactured hot tub. Made in their manufacturing plant in Fort Wayne, Indiana. Their UK supplier is Hot Tub Superstore and Grizzly Bear Hot Tubs. They supply and install all over the UK.
What should I do if my hot tub won’t turn on?
Remove the spa cover and allow water to cool. Once the heater has cooled, reset by pushing any button. If the hot tub does not reset, shut off power to the spa and call your supplier for a service. “Overheat” – The spa has shut down. One of the sensors has detected that the spa water is 43.3 degress C. DO NOT ENTER THE WATER.
What do I do if my Master Spa code is missing?
The code on Master Spa is normally an easy fix, however, if your Master Spa code is not listed, please call customer care 855-308-2149; we do offer limited technical support.